zoom_in
zoom_out
fullscreen
-70%
Ruko Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 27 mm 1081527C
Sku: T-12746
47,98 € (excl. legal VAT, excl. Shipping)
158,53 € MSRP
In stock,ready for shipping within 48h
Product variants
Sku: | Name: | SKU manufacturer: | ||
---|---|---|---|---|
T-12726 | Core drills Tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 19 mm | 1081519C | ||
T-12728 | Core drills Tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 20 mm | 1081520C | ||
T-12730 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 21 mm | 1081521C | ||
T-12732 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 22 mm | 1081522C | ||
T-12734 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 23 mm | 1081523C | ||
T-12736 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 24 mm | 1081524C | ||
T-12738 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 25 mm | 1081525C | ||
T-12741 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 26,5 mm | 10815265C | ||
T-12742 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 26 mm | 1081526C | ||
T-12745 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 27,5 mm | 10815275C | ||
T-12748 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 28 mm | 1081528C | ||
T-12750 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 29 mm | 1081529C | ||
T-12752 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 30 mm | 1081530C | ||
T-12754 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 31 mm | 1081531C | ||
T-12756 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 32 mm | 1081532C | ||
T-12758 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 33 mm | 1081533C | ||
T-12760 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 34 mm | 1081534C | ||
T-12762 | Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 36 mm | 1081536C |
doneInsert guide pin into core drill.
The RUKO core drills with Tecrona coating and carbide cutting edges can be used universally with non-hardened steels and superalloys (materials with very high alloy contents of AL, Ti, nickel such as Inconel, Husteloy, Inox). The Tecrona coating is the ideal coating for all drilling work that places extreme demands on the tool. It adheres very well to the tool, so the wear protection coating increases the surface hardness to approx. 4200 HV. The coefficient of friction with this coating is extremely low, which increases the service life with little wear.
Content:
1 Piece
Shipping:
The shipping costs for United Kingdom could not be calculated automatically.
Provider:
Sales and delivery by ToolTeam®
Payment methods:
Returns:
Security:
Product data
Manufacturer:
Ruko GmbH
Condition:
NEW
Sku:
T-12746
SKU manufacturer:
1081527C
GTIN Code (EAN):
4007140315595
Weight:
0,00 Kg
All information relating to products from Ruko GmbH. Technical and optical modifications of the manufacturer and errors reserved.
This page has been machine-translated, the original german version can be found here, please also note the Translation Disclaimer.
Product description
Ø 27,0 mm. Cutting depth: 30 mm - Can be used on all track drilling machines. The cutting geometry has been specially optimized for heavy duty chip removal from railway tracks, thus makes efficient use possible.; Advantages of the Tecrona coating; The Tecrona coating is ideal for all operations that are carried out without cooling or lubrication. It adheres very well to the tool, thereby increasing the surface hardness of the wear protection coating to approximately 4200 HV and the thermal resistance up to 1100°C. ; The coefficient of friction is very low for this coating, thereby increasing the service life with low wear.; Applications: ; Particularly for rail tracks, Hardox / Weldox steel, steel, cast iron, high-alloyed chromium steel such as stainless and acidresistant steel.
- Tecrona core drill coated with hard metal cutting edges and Weldon shank 3/4” for railway tracks. Ø 27 mm
- Can be used on all rail drilling machines. The cutting geometry has been optimized especially for heavy-duty machining of railway tracks and thus enables economical use.
- They have a drilling time that is up to 10 times shorter than with twist drills. Core drills only machine the tooth width, the drill core is ejected. Lower energy requirements and less wear result in a long service life.
- With twist drills, the entire drill diameter must be machined. This requires a lot of force and a high drive power.
- Insert the guide pin into the core drill.
- Push the core drill into the holder and tighten the hexagon socket screws.
- Make sure the core drill is properly seated in the holder.
- With the EasyLock quick-release holder, the core drill is automatically locked.
- Drill to size immediately, no need for punching or pre-drilling.
- The cutting geometry of the core drill enables rapid chip removal upwards.
- The spring-loaded guide pin helps to release the cut-out pieces.
- Observe the speed table and use coolant.
Additional information
Diameter:
27,0 mm
Schneiden:
Hartmetall + Tecrona Beschichtung
Schnitttiefe:
30,0 mm
Maschine:
RS5e / RS10 / RS20 / RS25e / RS30e / RS40e
Ø Weldonschaft:
19mm (3/4")
Schaftdurchmesser mm (2):
19,00
Schaftdurchmesser mm/Zoll/MK Maßeinheit:
mm
Schaftdurchmesser Zoll / MK:
3/4
Nettogewicht:
0,1 kg
Related results
Complete catalogs
The offer is aimed exclusively at business customers, companies, public institutions, tradesmen and freelancers. All prices in catalogues are exclusive of VAT, shipping costs and surcharges if applicable.
The manufacturer is exclusively responsible for the content, price and article details of the products and offers presented in the catalogues. Subject to technical and optical changes by the manufacturer and errors excepted.
The manufacturer is exclusively responsible for the content, price and article details of the products and offers presented in the catalogues. Subject to technical and optical changes by the manufacturer and errors excepted.
Matching catalog
Commercial customer offer**
Product suggestions
-62%
Hand tap UNF DIN 2181 HSS, taper tap, ground 3/4”
246034UNF1
12,14 €
32,14 € MSRP
-70%
Core drill Tecrona coated with tungsten-carbide and Quick IN-shank. Ø 45 mm
1081145C
84,50 €
282,65 € MSRP
-56%
Twist drills DIN 1897 type N HSS Co 5 ground, with split point - short
202050E
2,31 €
5,29 € MSRP
-37%
Twist drill DIN 338 type N HSS rolled
201061
0,71 €
1,13 € MSRP
-65%
Twist drill DIN 338 TL 3000 HSSE Co 5
229083
4,50 €
12,90 € MSRP
-64%
Twist drill DIN 338 TL 3000 HSS TiAlN
258160F
20,41 €
56,39 € MSRP
-65%
Set of HSS bi-metal hole saws in plastic cases
106305
56,60 €
159,45 € MSRP
-63%
Machine tap M DIN 376 HSS Co 5 M 22
233220E
29,87 €
80,38 € MSRP
-59%
Glass and tile drill with carbide cutting edge and straight shank
223008
6,55 €
15,92 € MSRP
-63%
Round dies M DIN EN 22568 HSS, ground M 30
237330
31,47 €
84,79 € MSRP
-57%
SDS-plus hammer drill
211040
3,66 €
8,53 € MSRP
-61%
Twist drill DIN 338 type N HSSG-TC Tecrona 3.3
815033C
9,40 €
24,41 € MSRP
-60%
UC Twist drill FLOWSTEP TIP DIN338 HSSCo, 2.5 mm, cyl.
259025E
2,68 €
6,72 € MSRP
-55%
Twist drill DIN 338 type VA HSSE Co 8
281080E
6,60 €
14,79 € MSRP
-59%
Centre drills DIN 333 HSS shape A
217050
7,06 €
17,31 € MSRP
No Review yet
Description: No Review yet
Written by: No Review
Rating: 5 out of 5
5 stars, based on 1
reviews
Ruko Core drills tecrona coated with tungsten-carbide cutting edges and Weldon shank for railway tracks. Ø 27 mm 1081527C
Ø 27,0 mm. Cutting depth: 30 mm - Can be used on all track drilling machines. The cutting geometry has been specially optimized for heavy duty chip removal from railway tracks, thus makes efficient use possible.; Advantages of the Tecrona coating; The Tecrona coating is ideal for all operations that are carried out without cooling or lubrication. It adheres very well to the tool, thereby increasing the surface hardness of the wear protection coating to approximately 4200 HV and the thermal resistance up to 1100°C. ; The coefficient of friction is very low for this coating, thereby increasing the service life with low wear.; Applications: ; Particularly for rail tracks, Hardox / Weldox steel, steel, cast iron, high-alloyed chromium steel such as stainless and acidresistant steel.
4007140315595-60
4007140315595
https://www.toolteam.com/en-GB/ruko-core-drills-tecrona-coated-with-tungsten-carbide-cutting-edges-and-weldon-shank-for-railway-tracks-o-27-mm-1081527c-t-12746-4007140315595.html?dc=GB&cu=EUR
2024-09-23
47.98
DE
14